top of page

Replacement Roofs for A-Frame Tents from 6 to 20 m Wide

Sep 23
5 min read

Updated: Sep 30

When the roof of an A-frame tent tears or wears out, the aluminium or steel frame is usually still fine: all you need is a new made-to-measure roof. In Málaga we make replacement PVC roofs for tents 6, 8, 10, 12, 15 and 20 m wide, for any brand of frame, either as keder panels, one per bay, or as a single piece.

This guide explains how the roof of an A-frame tent is organised, how to tell which system yours uses and which measurements to send us for a quote.

Common spans and 3 or 5 m bays

An A-frame tent is defined by two figures: its width, or span, between the legs of one frame, and its length, which is built up from bays, the modules between two consecutive frames. The most common spans are:

  • 6 and 8 m: smaller tents for events, fairs or light storage.

  • 10 and 12 m: very widely used sizes for events, catering and storage.

  • 15 and 20 m: large tents for events, temporary halls and warehouses.

Bays are usually 3 or 5 m long. So a 10 × 25 m tent has 5 bays of 5 m, and a 6 × 12 m tent has 4 bays of 3 m. Even so, every frame manufacturer has its own profile sizes, roof pitch and heights, which is why we always work from the actual measurements rather than the model name.

Aluminium frame of an A-frame tent seen from inside, with the PVC roof pulled taut

Keder bay panels or a one-piece roof

The first thing to find out is which system your tent uses, because it completely changes how the roof is made:

  • Keder roof, one panel per bay: on tents with aluminium profiles, each roof panel has a cord along its edges, the keder, which slides into the groove of the frame profiles. There is one panel per bay, running from one eave over the ridge to the other. This is the usual system on medium and large modular tents, and it has one clear advantage: if a panel is damaged, only that panel needs replacing.

  • One-piece roof: a single cover spans the whole roof and is tensioned over the frame with straps, ropes or tensioners. It is more common on small or lightweight frames. It goes up quickly, but if it tears, the whole piece has to be repaired or replaced.

If you do not know which keder your tent uses, our guide what a keder is and how to find out which one your tent has explains how to identify and measure it.

Gable ends and side walls

The roof rarely comes on its own. At each end of the tent there is a gable, the triangle between the eaves and the ridge, and below the eaves the sides are closed with side walls, usually one per bay on each side. All these parts can be ordered with the roof or separately, in opaque, translucent or transparent fabric.

For 10 m tents we have a detailed guide to side walls and gable ends for 10 m tents.

Real project: PVC grandstand roofs and 288 tent side walls, made in Málaga for a major motorsport event in Madrid. See the project

Which fabric to use for the roof

We make roofs from polyester fabric with a PVC coating, in 650 or 850 g/m², waterproof, with anti-mould treatment and UV protection. For roofs the usual choices are:

  • Opaque white: the most popular option for events and storage; it gives shade and keeps light off whatever is inside.

  • Translucent: lets diffused daylight through, useful when you want to work or hold an event inside without switching the lights on during the day.

  • Coloured: several colours are available in opaque fabric, to match an event's or a brand's look.

Our PVC fabric has fire class T2 under the European standard UNE-EN 15619, tested to EN 14115 by AITEX (reports 2024AN2176 and 2024AN2177). Organisers and local authorities often ask for this information for tents that are open to the public.

Which measurements to send for a quote

To make a roof that fits first time, we need:

  1. Width or span: the distance between the centres of the legs of one frame.

  2. Bay length: the distance between the centres of two consecutive frames (3 m, 5 m or other).

  3. Number of bays: or the total length of the tent.

  4. Keder: the diameter of the cord or, better still, a photo of the old keder and of the profile groove with a ruler next to it.

  5. Heights: eaves height and ridge height, measured from the ground.

  6. Photos of the profile: one photo of the cross-section of the aluminium profile and another of the whole tent.

  7. Parts: whether you need only the roof or also gable ends and walls, the type of fabric and the colour.

Quotes are free and without obligation. Manufacturing time is confirmed with each quote, and transport across Europe takes about one week once the goods leave our factory. You will find more information on our A-frame tents and replacement tent covers pages.

Frequently asked questions

Can you make a roof for a tent from another brand?

Yes. We make roofs, gable ends and walls for frames of any brand. What matters is the actual size of the frame, the bay and the keder, not who made the tent.

Can I replace just one roof panel?

If your tent has a keder roof with one panel per bay, yes: you can order one or more individual panels. Tell us the colour and fabric of the panels that are staying so that the roof looks as even as possible.

Which fabric weight is best for a 15 or 20 m roof?

We work with 650 and 850 g/m² fabric. For large roofs and for tents that are put up and taken down often, 850 g/m² is usually chosen for its greater strength. We will advise you based on use, wind exposure and the type of frame.

How do I measure the keder if I no longer have the old roof?

Measure the inside width of the groove in the aluminium profile, or send us a photo of the profile cross-section with a ruler next to it. That is enough for us to identify the right keder.

Send us the span, the bay length, the number of bays and a few photos of the profile, and we will prepare a quote for your new roof.

 
 
 

Comments


  • WhatsApp Plastold
bottom of page